|

Free Shipping Offer

Get free Standard Shipping with your $50 purchase today!

Please note this offer is only available to physical shipping addresses in the 48 continental United States (no PO Boxes), and oversize charges still apply on some heavy/large items.

(21)

Hope Pro 2/ Evo Front Hub Conversion Kit

Item #: HU510Z00
USD$26.99 SAVE 16% USD$32.29 msrp
Qty
Found a Lower Price?

Hope Pro 2/ Evo Front Hub Conversion Kit

These conversion kits let you customize your Hope hubs to fit different dropout styles and widths. Front conversion kits work on both Pro 2 and Pro 2 Evo hubs. Rear conversions must specify Evo.
4.7 / 5.0
21 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
18
1
1
1
0
Conversion Kits
Hope hubs are on par with many of the premium brands for a lot less $. The hubs are easily converted from different axle types in less than 30 seconds without tools. I ride ridgid bikes during the winter. I easily converted a 15mm thru axle to a 9mm thru bolt with this kit for my winter setup.

PROS: Easy To Install
January 2, 2013
Location:
Cincinnati, OH
Very easy to install, work great
I love my Hope Pro 2 hubs, but needed to upgrade to a 15mm through axle (Maxle) when I built up a new bike with a RockShox fork. These worked perfectly - quick and easy to install. A bit pricey, but absolutely necessary.

PROS: Durable, Easy To Install, Lightweight

BEST USES: Upgrade, Racing, Mountain Biking
October 27, 2014
Location:
Chicago, IL
One wheel for two bikes
Now I can use the same wheel and tyre in two differents bikes. One with 15 mm axle and other with standart QR 9 mm.

PROS: Easy assembly, cheap
September 17, 2012
Location:
Belo Horizonte, Brazil
The Best
These adapters made the purchase of a used hub a cost effective solution to a nagging problem. The original 'ends' pulled off and after a quick cleaning and servicing of the hub the new adapters were installed and the wheel was ready for new service.

PROS: Quality of fit, Ease of installation, Appearance
May 16, 2012
Location:
Phoenix, AZ
Great (as expected)
Simply pull off the other hub fittings with your fingers. Push these in with your fingers. Takes about 15 seconds. As always, grease is your friend.

PROS: Simple, Tool free
April 12, 2012
Location:
Reno, NV
Easy as Pie
I have a Hope Pro II EVO 20mm thur-axle front HUB and not have a 15mm QR front fork so i purchased this conversion kit. It did not come with any instructions on how to install but it was pretty self explanitory.

The 20mm cups are held in by metal retainer clips. There is a little notch taken out of one of the ends of the metal retainer clip. If you use a small flat head screw driver, you can pop the retainer clip right out. Once the retainer clip is out, you can pull the 20mm cup out of the HUB exposing the bearing. Take your 15mm cup and put a little grease on it and press it into the HUB over the bearing. There is no retainer clip for the 15mm cups so be careful not to let them fall out. Repeat for the other side, install your wheel and go ride!

This is a very simple and easy to convert HUB but it bothers me that there is no retention system for the 15mm cups like there are for the 20mm cups. Its not a huge deal but its nice for when you are on the trail and have to pull off your wheel for a flat, you wont accidentally lose the cup. Other then that awesome product!

PROS: Well Made, Easy To Install, Exact fitment, Rubber seals

CONS: No retention system

BEST USES: Hope Pro II Conversion, all-mountain
April 10, 2012
Location:
Sacramento, CA
Easy conversation
Great product... Converts front hub to 15mm

PROS: Easy To Install, Durable, Attractive Design

BEST USES: Mountain Biking, Upgrade, Racing
November 3, 2014
Location:
Raleigh, NC
Super easy to install. No tools needed.
I originally purchased hope hubs because I knew that I would upgrade to a thru axle fork. Well, I finally did that and the conversion kit made it super easy. Pull out the QR pieces, and install the thru axle pieces. No tools needed.

PROS: Attractive Design, Lightweight, Easy To Install, Durable

BEST USES: Racing, Mountain Biking
September 19, 2014
Location:
AZ
The right tools make it easy to install
These pieces can be difficult to get in or out. After damaging one trying to get it out I realized how easy they are to remove. Use the largest socket that will fit inside and thru the hub. Place an extension on the socket and tap the end of the extension with a mallet. Hope that helps

PROS: Didn't Have To Buy Hubs

CONS: Difficult To Install
September 8, 2014
Location:
Kansas City
Beautifully made and easy to install
When I changed forks the new Fox had option for cross axle, so I jumped at the chance. Simple switch out to install, fit perfectly. I could feel the added strength and stability from the first ride!

PROS: Lightweight, Durable, Easy To Install, Attractive Design
December 6, 2014
Location:
Exton, PA

Q & A

Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions
Can this applicable for Pro 4 front Hubs?
ThomaslkTang on Oct 17, 2016
Can this be used to convert a hope pro 4 20mm to 15mm
Caleb on May 24, 2016

Jenson USA ships worldwide, including APO/FPO addresses. For a quote, simply add the items you are interested in to your shopping cart and look for the "Shipping Options" box. You don't have to login or create an account to see shipping charges.

Some manufacturers restrict where we can ship their products. If this item has shipping restrictions, they are listed below. If you'd like to buy an item that we cannot ship to your preferred address, we can accept your foreign credit card and ship to a USA address for you.

Get free shipping with your $50 purchase today when you choose Standard Shipping at checkout. Please note this offer is only available to physical shipping addresses in the 48 continental United States (no PO Boxes), and oversize charges still apply on some heavy/large items

Customers Also Bought
Related Products
Stan's NoTubes 3.30 Type 2 Rear XD Caps
NoTubes 3.30 Rear End Caps Type II Use ...
Stan's NoTubes 3.30 Type 2 Rear XD Caps
Stan's NoTubes 3.30 Type 2 Rear XD Caps
Description:
NoTubes 3.30 Rear End Caps Type II Use these Stan's hub endcaps to convert Stan's 3.30 Type II Disc rear hubs to Quick Release or 10x135 thru bolt. Note: The Type II hub can be identified by the stainless steel ...
Thule Shimano Thru-Axle Adapter
Thule Shimano Thru-Axle Adapter The Thule Shimano Thru-Axle ...
Thule Shimano Thru-Axle Adapter
Thule Shimano Thru-Axle Adapter
Description:
Thule Shimano Thru-Axle Adapter The Thule Shimano Thru-Axle Adapter allows for Thule child carriers to be compatible with bikes with 12mm E-Thru rear axles. Installation is easy and headache free. Thule Shimano Thru-Axle Adapter Features 12 mm Shimano E-Thru Axle ...
Easton X4 Front End Cap
Easton X4 Front End Caps Genuine Easton parts ...
Easton X4 Front End Cap
Easton X4 Front End Cap
Description:
Easton X4 Front End Caps Genuine Easton parts for wheels with Easton X4 hubs. These will adapt a front hub to work with a tradition 9x100mm quick release. Specifications Fits X4 Hubs Size 9x100 QR Sold Individually

Need Gear Advice?

Our Gear Advisors are Ready to Help

Email Specials

Sign up for our weekly newsletter delivered via email.

Keep Pedaling

Free Shipping Offer

Get free Standard Shipping with your $50 purchase today! Just choose Standard Shipping during checkout.

Please note this offer is only available to physical shipping addresses in the 48 continental United States (no PO Boxes), and oversize charges still apply on some heavy/large items.